SkullandBonesSkateboards.com Forum Index » B.O.N.O.S.A. » G&S Chromoly Pivot Cups |
Page 1 of 1 |
|
Author |
Message |
10x30 |
Posted: Wed Aug 25, 2021 2:44 pm |
|
|
Joined: 25 Aug 2021
Posts: 1
Location: Los Angeles
|
I have a set of the G&S Chromoly trucks with the plastic base plates and after 30+ years the pivot cups crumbled apart.
Like everything about these trucks they were a proprietary design so fairly impossible to find and would also be 30+ years old too.
Was wondering if anyone else found a decent replecement. I'm using Indy pivot cups now but they don't quite fill the baseplate pocket so the axle's pivot point shifts around a bit. I ride loose trucks but it's a bit too sketch.
Thanks in advance for any help! |
|
|
Back to top |
|
|
swelbow |
Posted: Wed Aug 25, 2021 5:10 pm |
|
|
ORDER OF THE SKULL
![ORDER OF THE SKULL ORDER OF THE SKULL](http://www.skullandbonesskateboards.com/isupporttheskull.gif)
Joined: 29 Nov 2009
Posts: 650
Location: lonely desert
|
I thought about trying to make them with 3M window urethane like the car guys do with motor mounts. Kind of expensive to buy that giant tube to make such little things. Lathe them out of delrin?
Make some and sell them |
_________________ super sonic skate park |
|
Back to top |
|
PyratMike |
Posted: Wed Aug 25, 2021 9:02 pm |
|
|
Joined: 03 Mar 2021
Posts: 146
|
|
Back to top |
|
|
steve-g |
Posted: Thu Aug 26, 2021 4:03 am |
|
|
ORDER OF THE SKULL
![ORDER OF THE SKULL ORDER OF THE SKULL](http://www.skullandbonesskateboards.com/isupporttheskull.gif)
Joined: 17 Jul 2003
Posts: 7292
Location: UK.
|
Those dudes may be able to make a custom order if you supply the specs. If you have access to a lathe you could make your own from some polyurethane or machine down a large bottom bushing. |
|
|
Back to top |
|
steve-g |
Posted: Thu Aug 26, 2021 4:15 am |
|
|
ORDER OF THE SKULL
![ORDER OF THE SKULL ORDER OF THE SKULL](http://www.skullandbonesskateboards.com/isupporttheskull.gif)
Joined: 17 Jul 2003
Posts: 7292
Location: UK.
|
Oh yeah, need to add - those G&S trucks were the best for slappies and sparks! I loved their grind but hated that the kingpin would snap and couldn't be removed from the baseplate. I gave up on them after two pairs. |
|
|
Back to top |
|
burrowed |
Posted: Mon Nov 27, 2023 8:41 pm |
|
|
Joined: 27 Nov 2023
Posts: 1
Location: toronto
|
I tried this the other day to fix old gullwing. The pivot bushing was totally gone and I probably rode them for years like that damaging the pin on the hanger. I built the pin back up with JB weld (2 part epoxy). I haven't ridden them yet, but it should work. |
|
|
Back to top |
|
|
slob-air |
Posted: Tue Nov 28, 2023 12:50 pm |
|
|
Site Admin
Joined: 27 Oct 2001
Posts: 63458
Location: S&B HQ
|
Hot glue gun -- fill the pivot cup, plunge the pivot arm into it and let it set-up. Works not bad at all. |
_________________ >>>>>Get your S&B Stickers here<<<<< |
|
Back to top |
|
|